Skip to main content

Special Deals

Below, you'll find some special deals and coupons I managed to get a hold of for you, if you are interested in buying from China. It takes a while to arrive, but the base price is way much cheaper already, and with these deals, you will save even more! 😁
If you select "Priority Line" during checkout as the shipping method, your product will arrive sooner, and get less customs hassle, for free, or a very small amount (depending on size and weight of the total package)

 Most deals have a quantity and/or time limit on them, so read well, be quick, and check back regularly for new deals!


Today's promotion:




https://www.banggood.com/custlink/GG33WUZjGH

€ 112.31
=======================================================

https://www.banggood.com/custlink/GmKGrkZoDS
€ 10.76
If you are interested in other than RC related discounts as well, and coupon codes to make that all even cheaper, then be sure to check out this facebook page:
https://www.facebook.com/NoHurries
This will give you access to various coupon codes that make those prices even lower than the already low Chinese prices. Even lower than the Chinese Flas Sale prices!
There's lots of interesting stuff around there, like phones, tablets, and computers, but also vacuum cleaners, 3D printers, and smart watches. Go check it out!

Comments

Post a Comment

Popular posts from this blog

Tevo Tarantula prints

I am very happy with my Tevo Tarantula 3D printer! I have it up and running for about 6 weeks now. Let me tell you about my prints so far! Reading all the forums, facebook groups, and of course the Tevo website, I decided on the way forward after finishing the build. First, I would need to be able to print dimensionally reasonably accurate parts. In order to achieve that, I fist took a  look at the extrusion. It is important that the extruder extrudes the commanded length of filament, to within a few percent. To check that, I fed in the filament for only a few centimeters. With that as "0", I measured 120mm from the infeed side of the extruder, and marked the filament with a black marker. Then, I commanded the extruder to feed 100mm into the teflon tube, and mesured how far from the extruder infeed side the mark ended up. That should be 20mm, of course, but in my case it was less than that. So I had to tune down my extruder a bit. As I measured 17mm, it had "over-...
1 comment
Got you interested? Read more »

ZOHD Talon GT with Matek F405 WING, GPS, BlueTooth, FPV, Long Range - Part 1

This is going to be a small series of me assembling a ZOHD Talon GT in an INAV configuration. I have the Talon on order already, and am waiting for it to arrive. Banggood was kind enough to supply me with a MATEK F405 WING flightcontroller, a Ublox M8N GPS , and an FrSky XM+ receiver to test this configuration 😁 The Talon was paid for regularly, mind you. Just to be clear and transparent on that. This makes an INAV configuration possible, but the most obvious next step would be to introduce a long-range transmitter module / receiver combo. The XM+ shoud have a decent enough range to fly line of sight, and maybe some FPV, a little further out, but an FrSky R9M setup (ca. €100), or even better: a Crossfire setup  (ca. €200), would be the way to go for this type of flying. I don't have those yet, so donations are always welcome! That can be as simple as clicking on any of the (affiliate product links in this blog, and ordering something from those stores that are linked. It do...
1 comment
Got you interested? Read more »

Binding FrSky S8R stabilizing receiver

What could be easier than binding a receiver to a transmitter, right? Push the bind button while powering up the receiver, put the transmitter in binding mode, wait a few seconds, done! Well ... With the FrSky S8R receiver, there are a few "other possibilities"...
3 comments
Got you interested? Read more »